Gastroback 41402 Istruzioni per gli Interventi Scaricare il pdf (Pagina 5)

2. Detach the worm housing from the motor block.

3. Unscrew the closing ring turning it counterclockwise.

TIP: If the closing ring is screwed on to tight you can use a

screwdriver as shown in the picture 10.

4. Remove the grinding disc. If necessary insert a knife or

screwdriver between the grinding disc and the worm housing

to pry out the grinding disc.

5. Remove the crossed-blade knife and pull out the worm or if you

used the chopper attachment remove them.

TIP: If the tools are stucked knock the mincer carefully on a stable cutting board. The grinding

disc should be facing up.

ATTENTION: Be careful not to damage your bench top, the cutting board or the mincer.

6. Remove meat residues.

Operate as described:

ATTENTION: Never put the appliance or parts of the appliance

in the dishwasher or use abrasives for cleaning! This will cause

discoloration and corrosion.

7. Wash all parts thoroughly in hot soapy water. Do not use aggressive detergents. The parts

are not suitable for dishwasher. Soak parts with desiccated food leftovers a few minutes in

warm soapy water and use a nylon cleaning brush or cleaning sponge for cleaning. Rinse

all parts with running water and dry them accurately.

WARNING: Ensure that the switch and cable do not come into contact with water!

Should this inadvertently happen, all parts must be completely dry before the appliance is used

again. Never let water or other liquids run into the motorblock. Never clean the line cord

or the appliance in the dishwasher, poor liquids over the appliance or douse or dip it in water

or other liquids. In case that water or other liquids ran into the appliance while operating turn

OFF the appliance immediately, pull the plug and dry the appliance with a clean cloth.

8. The motor block must only be wiped clean with a moist cloth. Do not clean the motor block

under flowing water, nor should it be immersed in water! Do not use alcohol, benzine, etc.!

9. Grease the grinding disc and knife with salad oil to prevent air corrosion.

Storage

Always clean the appliance before storing.

ATTENTION: Store and use the appliance in a clean, frost free environment where it is

protected from dampness, moistness and immoderate and extraordinary burden (such as:

downfall, beat, overheating, moisture in the motor block). Never lay heavy or hard objects

on top of the appliance.

4. Assemble the appliance this time with the chopper attachments.

IMPORTANT: Never assemble the appliance with the

chopper attachment AND the crossed-blade knife with the

grinding disc

a. Assemble the worm housing in the opening of the drive shaft.

Place the worm inside the worm housing (operate according to

the instructions ´Assembling` the appliance. see fig. 1 and 2).

b. Place the chopper attachment A on the axis of the worm.

The slim end has to face the front (see fig. 7). Turn the chopper

attachment a little bit while pushing it into the worm housing.

c. Place the chopper attachment B on top of the chopper

attachment A. The wide opening of the chopper attachment B

should be facing the chopper attachment A. The chopper

attachment B has a gap on the outside edge which should slide

over the guiding pin on the inside of the worm housing (see fig. 8).

d. Attach the closing ring to the worm housing and screw it on

tight with your hands.

5. Process the wrapping mixture in the mincer with the attached

chopper attachments (see fig. 9). The finished product will be one

long wrapping. Cut the wrapping into convenient seize.

6. Freeze the wrapping shortly.

7. Fill the wrapping with the filling mixture.

8. Fry the wraps with some olive oil until it has the favored

browning.

Care and cleaning

WARNING: Never hold your face or other body parts over

the feed funnel when the motor is running because little pieces of food could be thrown out

of the feed funnel. Never put foreign substance or hard objects into the feed funnel.

Before the mincer is used for the first time, all parts – with the exception of the motor block –

must be thoroughly cleaned in warm soapy water.

Disassembling

WARNING: To avoid injury and damages of the appliance turn the appliance OFF

and then wait for approx. 6 seconds to be certain that the motor is no longer

running. Always pull the plug before you start disassembling or cleaning

the appliance.

1. Switch off the mincer and disconnect the power supply cable from the mains. Check that

the motor has completely stopped.

2726

1 2 3 4 5 6 7 8

Commenti su questo manuale

Nessun commento

Gastroback 41402 Istruzioni per gli Interventi Pagina 5

Commenti su questo manuale

Prodotti e manuali riguardandi Tritacarne Gastroback 41402